DMX512/RDM Series 

DMX is a lighting protocol that allows all lamps to be set independently of each other. The DMX512 protocol can set 512 addresses (8 bit) via RS485. The protocol is standardised and has been used for many years in the lighting industry.

In addition to the DMX512 protocol, the RDM (Remote Device Management) protocol can be used. This allows you ...

DMX is a lighting protocol that allows all lamps to be set independently of each other. The DMX512 protocol can set 512 addresses (8 bit) via RS485. The protocol is standardised and has been used for many years in the lighting industry.

In addition to the DMX512 protocol, the RDM (Remote Device Management) protocol can be used. This allows you to configure lamps that have already been hung up. It increases the flexibility of the network. RDM thus provides feedback of data in the entire configuration.

A DMX decoder can convert the universal digital signal DMX512/1990 into CC/CV PWM signal with advanced microelectronic control technology to control the LED. The control works via a DMX512 console and achieves a brightness of 0-100% or a changing color effect. It is possible to control single color, CCT, RGB, RGBY, RGBW and RGBA

Show more

Subcategories

DMX512 Master controller

DMX512 Master controller is the output signal of international standard DMX512/1990. It not only can control all the LED lights that receiving the standard DMX signal in the market, but also can work with our DMX decoder to control the general LED lights without DMX512.

  • WiFi-RDM01

    WiFi-RDM01 is the RDM master control, which browsing and setting corresponding parameters of the equipment with RDM protocol through the RDM standard protocol. WiFi-RDM01 uses the WiFi module, which can wireless control by the phone's APP and support to upgrade the firmware remotely. which is convenient for customers' using the most functional and latest firmware version. WiFi-RDM01 can be compatible with other brand's product with RDM protocol, and it does not affect the normal operation of other products when hangs on the bus.

      € 153,54
  • EX4S

    - Adopt wireless RF and wired DMX512 protocol 2 in 1 control mode, more flexible and convenient for project installation. - Advanced RF wireless sync/zone control technology, make sure dynamic color modes synchronously among multiple drivers. - Install touch panel at different areas, can control the same LED light, achieve multi-panel control, no quantity limited. -  Touch keys with chord and LED indicator. - Adopts capacitive touch control technology makes LED dimming selection more user-friendly. - Compatible with remote and APP control.

      € 99,75
  • EX8S

    - Adopts capacitive touch control technology on the full color wheel, make LED color selection more user-friendly. - Adopt wireless RF and wired DMX512 protocol 2 in 1 control mode, more flexible and convenient for project installation. - Advanced RF wireless sync/zone control technology, make sure dynamic color modes synchronously among multiple drivers. - Four zones can be combined arbitrarily, for example: zone 1 and zone 2 as a group, or zone 1, zone 3, zone 4 as a group, or all the 4 zones as a group. - Support multiply panels linkage control, no quantity limitation. - Touch keys with chord and LED indicator. - Compatible with remote and APP control. - No limit the quantity of drivers in each zone, and all color modes keep synchronously

      € 114,98
  • UX5

    The UX5 LED Dimmer Touch panel gives you the opportunity to easily Dim your LED lights. You can select the brightness by moving your finger over the bar in the middle. In addition, the UX5 has four zones. You can save your setting with the buttons I or II. The UX5 sends a DMX or a 2.4GHz RF signal. Through the DMX signal it can be controlled by connecting DMX controllers. DMX controllers which can be used for this are the LT-801-12A or LT-811-12A. Via the 2.4GHz RF signal it can be wirelessly controlled, here you connect the UX5 with R4-5A or R4-CC receiver. When using PWM Constant Voltage LED lighting you need the LED Receiver R4-5A and when using Constant Current lighting, you need the R4-CC, where you have the choice of 350mA / 700mA / 1050mA control. The UX5 can collaborate via RF 2.4GHz with the V5 remote, making it possible to operate remotely as well as manually. Via a WiFi signal, it is possible to connect the UX5 with the WiFi-104. This makes it possible to control via the app on your phone or tablet. The UX5 has a universal backplate for all kind of wall boxes.

    € 130,66 € 45,73
  • UX8

    The UX8 LED Dimmer Touch panel gives you the opportunity to easily control your RGBW LED lights. You can choose the colors by moving your finger over the color wheel in the middle. In addition, the UX8 has four zones which can be selected via the buttons 1 to 4 at the top of the panel, you can create scenes and store them with the buttons I to IV, there is a mode feature with 11 different modes, brightness control by zone, speed function and separate brightness control per color. To control the white light there is the W button by pressing it briefly the white light goes on or off, and by keeping it pressed you can dim the white light. The UX8 sends a DMX or a 2.4GHz RF signal. Through the DMX signal the 4 zones can be controlled by connecting DMX controllers + LED control lights. DMX controllers which can be used for this are the LT-840-6A or LT-820-5A. Via the 2.4GHz RF signal the four zones can be wirelessly controlled, here you connect the UX8 with R4-5A or R4-CC receiver. When using PWM Constant Voltage LED lighting you need the LED Receiver R4-5A and when using Constant Current lighting, you need the R4-CC, where you have the choice of 350mA / 700mA / 1050mA control. The UX8 can collaborate via RF 2.4GHz with the V8 remote, making it to operate remotely as well as manually the four zones on the panel. Via a WiFi signal, it is possible to connect the UX8 with the WiFi-104. This makes it possible to operate the four areas next to the wall panel and remote control via the app on your phone or tablet. The UX8 has a universal backplate for all kind of wall boxes.

      € 152,15
Showing 1 - 0 of 1 item

CV DMX512 Decoder

DMX Decoder adopted the advanced micro-electronic control technology to convert universal DMX512/1990 digital signal to CC/CV PWM signal to drive LED, which controlled by DMX512 console, realize 0-100% brightness or various changing effect. And can control single color, dupi-color, RGB, RGBY, RGBW, RGBA LED lights.

Showing 1 - 0 of 1 item

CC DMX512 Decoder

DMX Decoder adopted the advanced micro-electronic control technology to convert universal DMX512/1990 digital signal to CC/CV PWM signal to drive LED, which controlled by DMX512 console, realize 0-100% brightness or various changing effect. And can control single color, dupi-color, RGB, RGBY, RGBW, RGBA LED lights.

  • LT-880-350

    LT-880-350 with the standard RDM remote device management protocol, supports DMX512 signal bi-directional communication, achieves remote management of reading and writing DMX address (DMX master controller must recognize the RDM protocol). This compact decoder works with DMX512 console. Realize 0-100% brightness and various changing effect. Equiped with DMX standard XLR-3, RJ45 and green terminal interface, easy to operate. And it can control single color, bi-color, RGB LED lights.

      € 286,00
  • LT-830-700

    The 700mA DMX decoder is suitable to control 700mA High Power LED's. A maximum of 12 pieces high power LED's can be connected to one 700mA DMX controller.

    € 97,94 € 34,28
  • LT-880-700

    LT-880-700 with the standard RDM remote device management protocol, supports DMX512 signal bi-directional communication, achieves remote management of reading and writing DMX address (DMX master controller must recognize the RDM protocol). This compact decoder works with DMX512 console. Realize 0-100% brightness and various changing effect. Equiped with DMX standard XLR-3, RJ45 and green terminal interface, easy to operate. And it can control single color, bi-color, RGB LED lights.

      € 288,58
  • LT-830-900

    The 700mA DMX decoder is suitable to control 700mA High Power LED's. A maximum of 12 pieces high power LED's can be connected to one 700mA DMX controller.

    € 97,94 € 34,28
  • LT-858-CC

    LT-858-CC with the standard RDM remote device management protocol, supports DMX512 signal bi-directional communication, achieves remote management of reading and writing DMX address (DMX master controller must recognise the RDM protocol). Realise 0-100% dimming or different lighting effects; works with DIM, CT, RGB,RGBW.

      € 81,55
Showing 1 - 0 of 1 item

DMX-SPI signal type

DMX-SPI signal decoder is to convert the DMX512 digital signal into SPI(TTL) digital signal. It can work on the DMX console to control the LED lights with compatible driving ICs. DMX console can control every channel of the LED Lights, realizing 0-100% dimming and various changing effect.

Our DMX decoder can control LED lights based on following driving ICs: MBI6120, LPD6803, LPD1101, D705, UCS6909, UCS6912, LPD8803, LPD8806, TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, TLS3001, TLS3002, WS2801, WS2803, WS2811, WS2812, P9813 IC etc.

The grey scales of DMX decoder depends on the driving IC, the above driving ICs are with a built-in grey scale processor and occupy 70-80% of LED digital lighting market, use our DMX-SPI decoder can simply turn normal LED digital light to DMX512 LED light with international standard communication protocol, which is easy to promote in the international market.

DMX-SPI decoders are widely used in the LED string light, LED dot light, SMD flexible strip, LED digital tube, wall light, pixel screen, high power spot light, wall washer and kinds of LED digital lights.

Showing 1 - 0 of 1 item

CV DMX512 Dimmable Driver

LTECH Intelligent dimmable led driver have excellent performance:

- Fully Digital circuit design, excellent performance and long working life
- PWM digital dimming, maintain the best LED’s CRI(color rendering index)
- Standard logarithmic dimming curve, the human eye visual feel more comfortable
- 60000:1 wide dimming range, 0-100% full dimming range,LED start at 0.1% possible
- Power factor>0.99, Efficiency>86%, THD(Total Harmonic Distortion)<10%
- Short circuit / Over-temperature /Over load protection
- Current consistent in multi LED driver working, balanced light
- Class 2 security isolation power supply
- Compliant with SELV(Safety Extra Low Voltage) standard

  • LM-75-24-G1M2

    - Dimming interface: DMX512/RDM, Push DIM. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Standby Power Loss < 0.5W. - Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application. 

      € 91,95
  • LM-75-12-G2M2

    - Dimming interface: DMX512/RDM, Push DIM/CCT - 2 independently SELV constant voltage output channels. - Constant power design, adjust different color temperature to keep the same brightness. - DMX/RDM DIM and color temperature adjusting driver. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - Color temperature adjusting range: 2700-6500K - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Standby Power Loss: <0.5W - Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application.

      € 95,55
  • LM-75-24-G2M2

    - Dimming interface: DMX512/RDM, Push DIM/CCT - 2 independently SELV constant voltage output channels. - Constant power design, adjust different color temperature to keep the same brightness. - DMX/RDM DIM and color temperature adjusting driver. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - Color temperature adjusting range: 2700-6500K - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Standby Power Loss: <0.5W - Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application.

      € 95,55
  • LM-100-24-G1M2

    - Dimming interface: DMX512/RDM, Push DIM. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Standby Power Loss < 0.5W. - Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application. 

      € 102,30
  • LM-100-24-G2M2

    - Dimming interface: DMX512/RDM, Push DIM/CCT - 2 independently SELV constant voltage output channels. - Constant power design, adjust different color temperature to keep the same brightness. - DMX/RDM DIM and color temperature adjusting driver. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - Color temperature adjusting range: 2700-6500K - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Standby Power Loss: <0.5W - Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application.

      € 109,06
  • LM-150-24-G1M2

    - Dimming interface: DMX512/RDM, Push DIM. - Supports RDM remote device management protocol. - Dimming range from 0-100%, LED start at 0.1% possible. - With soft on-an-off fade in function, visual more comfortable. - High Efficiency driver: efficiency 93%, PF > 0.98, THD < 6% - 0~100% flicker-free, achieve the level of exemption assessment. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - In line with the EU Energy Efficiency ErP directive, Standby Power Loss < 0.5W. - Full protective plastic housing with design for dismountable end-cover. - Compliant with Safety Extra Low Voltage standard. - Suitable for indoor Ⅰ/Ⅱ/Ⅲ type lamps application.  - 5 years warranty (Rubycon capacitor)

      € 133,00
Showing 1 - 0 of 1 item

CC DMX512 Dimmable Driver

LTECH Intelligent dimmable led driver have excellent performance:

- Fully Digital circuit design, excellent performance and long working life
-PWM digital dimming, maintain the best LED’s CRI(color rendering index)
- Standard logarithmic dimming curve, the human eye visual feel more comfortable
- 60000:1 wide dimming range, 0-100% full dimming range,LED start at 0.1% possible
- Power factor>0.99, Efficiency>85%, THD(Total Harmonic Distortion)<10%
- Wide rang voltage+optional arbitrary current, workable with led lights at different power
- Short circuit / Over-temperature /Over load protection
- Current consistent in multi LED driver working, balanced light
- Class 2 security isolation power supply,full protective plastic housing
- Compliant with SELV(Safety Extra Low Voltage) standard

  • SE-20-250-1000-W2M2

    - Dimming interface: DMX512/RDM, Push Dim - T-PWM digital dimming, present a perfect visual experience. - With RDM remote device management protocol. - Dimming range: 0~100%, LED start at 0.01% possible. - With soft-on and fade in function, visual more comfortable. - DIP switch for 16 optional currents' quick selection. - 0-100% flicker-free,High frequency exemption level. - Dimming interface with photoelectric isolation, in line with the latest safety standards, more safe and reliable. - In line with the EU energy efficiency ERP directive, standby power consumption < 0.5W Innovative thermal management technology, intelligent power life protection. - Over temp. / Over voltage / Over load / Short circuit protection, recover automatically. - Non-load output voltage 0V to prevent damages to LED caused by poor contact. - Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ. - 5 years warranty (Rubycon capacitor).

      € 76,55
  • SE-12-350-700-W1M

    - Dimming interface: DMX512/RDM - T-PWM digital dimming, present a perfect visual experience. - With RDM remote device management protocol. - Dimming range: 0~100%, LED start at 0.01% possible. - Flicker-free (IEEE 1789), achieve the level of exemption assessment. - Innovative thermal management technology, intelligent power life protection. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Class 2 power supply. Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ.

      € 42,95
  • SE-12-100-400-W1M

    - Dimming interface: DMX512/RDM - T-PWM digital dimming, present a perfect visual experience. - With RDM remote device management protocol. - Dimming range: 0~100%, LED start at 0.01% possible. - Flicker-free (IEEE 1789), achieve the level of exemption assessment. - Innovative thermal management technology, intelligent power life protection. - Over-heat / Over voltage / Over load / Short circuit protection, recover automatically. - Class 2 power supply. Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ.

      € 42,95
  • DMX-10-100-400-F1P1

    A Constant current DMX driver with built-in power supply. Directly connectable at 100-240 volts. Sends out PWM dimming and has a power load from 3.5 to 9.8W, 350mA current and a voltage range of 10 to 28VDC.NOTE! This product comes in 350mA!!Is also available on request in 100mA, 150mA, 200mA, 250mA, 300mA or 400mA versions. To request, send an email to info@ltech-led.eu or sales@inventdesign.nl

    € 31,02 € 10,86
  • DMX-15-100-700-E1A1

    - Dimming interface: DMX512/RDM, Push Dim. - With RDM remote device management protocol. - PWM digital dimming, no alter LED color rendering index. - Dimming range: 0~100%, LED start at 0.1% possible. - Multi-current & wide voltage, suitable for different power LED. - Short circuit / Over-heat / Over load / Non-load protection, recover automatically. - Non-load output voltage 0V to prevent damages to LED caused by poor contact. - Class 2 power supply. Full protective plastic housing. - Compliant with Safety Extra Low Voltage standard. - Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ.

      € 74,94
Showing 1 - 0 of 1 item

DMX Signal amplifier

DMX Signal Amplifier is dedicated to amplify, distribute, and insulate the signal that comes from the lighting system equipment when it is connected to the bus of DMX512.

- It’s specially designed for signal shaping amplification for DMX512 signal which attenuated after a long-distance transmission, realize extending the signal transmission distance.
- Need to use the multiple signals expansion output control, increase DMX l signal amplifier to distribute multi-channel control.
- 1 channel input, 2-3 channels distributed output, there is a independently photoelectricity insulation of >3KV between Input and output terminals, and output terminals among 3 channels, so as to avoid the expensive equipment such as light, DMX driver, precise digital lighting controller, being burnt by the possible high voltage which caused from the wrong wire connection and a broken equipment, also can avoid the signal interference between each DMX equipment, to assure it works safely.

Showing 1 - 0 of 1 item
  • WiFi-RDM01

    WiFi-RDM01 is the RDM master control, which browsing and setting corresponding parameters of the equipment with RDM protocol through the RDM standard protocol. WiFi-RDM01 uses the WiFi module, which can wireless control by the phone's APP and support to upgrade the firmware remotely. which is convenient for customers' using the most functional and latest firmware version. WiFi-RDM01 can be compatible with other brand's product with RDM protocol, and it does not affect the normal operation of other products when hangs on the bus.

      € 153,54
Showing 1 - 0 of 1 item
  • ARTNET-DMX-1

    ArtNet-DMX converter is the Ethernet Control System based on the ArtNet protocol, used to convert the Artnet network date package into DMX512 date, adopting high-speed ARM processor, stable and reliable working. Following Art-net standard protocol, it support RJ45 network interface and standard DMX512 output interface. Artnet-DMX-1 can be configured in one of two ways: ArtNet convert into DMX512, or DMX512 convert into Artnet.

      € 245,77
  • ARTNET-DMX-2

    ArtNet-DMX converter is the Ethernet Control System based on the ArtNet protocol, used to convert the Artnet network date package into DMX512 date, adopting high-speed ARM processor, stable and reliable working. Following Art-net standard protocol, it support RJ45 network interface and standard DMX512 output interface. Artnet-DMX-2 has two standard DMX512 date output port, output 1024 data in total.

      € 245,77
Showing 1 - 0 of 1 item